Furniture Factory
Care guide

How to care for your furniture

The furniture we make is built from EGGER boards and worktops. Their surfaces are hard-wearing and need no special care products, just a few simple rules. We’ve gathered them here, in short, from the manufacturer’s recommendations.

Which materials this covers

  • decorative boards (melamine-faced board)
  • PerfectSense lacquered boards (matt and gloss)
  • laminates (HPL) and laminate-faced boards
  • edging (the strip on the board edges)
  • kitchen worktops and compact worktops

The basic rules

  • Use a soft, slightly damp microfibre cloth.
  • Wipe along the grain, especially on deeply textured decors.
  • Always start with the gentlest method and the shortest contact time.
  • Test any new product first on a spot that doesn’t show.
  • For everyday cleaning, glass cleaner or warm water with a little soap is enough.
  • Wipe off grease as soon as possible, within 48 hours at the latest.
  • After rinsing, wipe with warm water and dry with a clean microfibre cloth so no streaks are left.
  • Don’t use steam cleaners.

What NOT to use

  • scouring powder, abrasive creams, steel wool
  • sponges with a rough side, melamine (“magic”) sponges rubbed hard, rough cloths: they leave shiny marks or scratches
  • wax, polish, furniture cleaners, “restoring” plastic cleaners
  • bleach
  • strong acids: heavy-duty descalers, drain cleaners, hydrochloric acid, oven cleaners, silver cleaners

Heavier soiling: 4 steps

  1. Spray on a little cleaner (degreaser or mild descaler) and leave it for 5 minutes at most.
  2. Clean with a fine, damp, non-abrasive microfibre cloth.
  3. Rinse with a clean cloth and warm water so no residue is left.
  4. Dry with a clean cotton or paper towel.

Repeat if needed. Follow the instructions on the product label. A product left on too long can discolour the surface, especially the edging.

Every day

  • Always cut on a chopping board, not straight on the worktop: knives leave marks.
  • Put hot pans from the hob or oven on a trivet, not straight on the surface.
  • Wipe up spills straight away, especially at joints and around cut-outs (sink, hob).

Dealing with stains

Dust, pencil, coffee, tea, juice, fingerprints, felt-tip, ballpoint, grease, oil

Light
Dry or damp cloth or paper towel; then dry.
Normal
Warm water, soft sponge, soap or a non-abrasive detergent; leave it briefly, rinse with clean water, dry.
Old / heavy
As for normal soiling, repeated.

Limescale, water marks, rust

Light
Damp cloth, then dry.
Normal
Warm water and a non-abrasive detergent, rinse, dry.
Old / heavy
A paste of detergent and water left overnight; for stubborn limescale, vinegar or 10% citric acid, only briefly. Not on PerfectSense.

Candle wax, wax crayon, lipstick, shoe polish

Light
Cloth, then dry.
Normal
First lift the wax with a plastic or wooden scraper (without scratching), then run an iron over absorbent paper on top, then clean as normal.
Old / heavy
Detergent paste overnight; if it doesn’t come off, a little acetone or spirit, then rinse and dry. Not on edging and not on PerfectSense.

Water-based paints, emulsion, PVA glue

Light
Damp cloth, straight away.
Normal
Warm water and detergent; if it doesn’t come off, acetone or spirit. Not on edging and not on PerfectSense.
Old / heavy
Soften with water or solvent and peel it off. Not on edging and not on PerfectSense.

Solvent-based paints, varnishes and glues, spray paint, stamp ink

Light
Straight away with acetone or spirit, then rinse with clean water and dry. Not on edging and not on PerfectSense.
Normal
Soften and peel it off; graffiti only with specialist products. Not on edging and not on PerfectSense.

Resins and two-component glues (e.g. polyurethane)

Light
Only before they set: straight away, with water or solvent, then rinse and dry.
Normal
Once set, they usually cannot be removed.

Silicone, sealant

Light
Wipe it off dry; if needed, a silicone remover; rinse with clean water and dry.

When using acetone or spirit: window open, no naked flames.

Watch out for

  • Edging: wipe off any cleaner straight away; left on the edging it can cause cracks or white marks. Solvents only heavily diluted.
  • PerfectSense matt lacquered fronts: they are anti-fingerprint, as long as you don’t use cream washing-up liquid, wax, polish or “restoring” cleaners. These leave a sticky film that collects dirt.
  • Dark colours: signs of use show more easily on dark decors than on light ones. This is not a defect.
  • Streaks after cleaning: they come from solvents, cold water or a cloth used too many times. Wipe again with warm water and dry with a clean microfibre cloth.

Frequently asked questions

What should I use to clean my kitchen furniture every day?

A slightly damp microfibre cloth and, if needed, a little soap or glass cleaner. Then dry.

Can I use a magic (melamine) sponge?

It isn’t recommended. Rubbed hard, it leaves shiny patches or scratches.

Do I need furniture polish or wax?

No. The surfaces need no care products, and wax and polish leave a film that collects dirt.

Can I use a steam cleaner?

No. The manufacturer advises against steam cleaning.

How do I remove limescale around the sink?

With warm water and a non-abrasive detergent. If it stays, vinegar or 10% citric acid, only briefly, then rinse and dry. Don’t use acids on PerfectSense fronts.

Why do marks show more on black or anthracite furniture?

Signs of use are more visible on dark colours. That is normal and not a defect.

Source: EGGER’s recommendations (“Cleaning and care recommendations for EGGER product surfaces”, rev. 02, 22.05.2026), PDF. This information is a guide; also follow the instructions on the cleaning product’s label.

Start a project

Got a tricky corner? Send it to us.

A question about your furniture, or need us to come and look? Message us on WhatsApp at +40 722 222 783 or through the contact page.

Chat on WhatsApp